主要針對汽車空調各種漏點,整個系統快速100%不會誤報,10-30分鐘,100%找出各種泄漏點,代替加壓力,灑水,熒光粉,拆系統在水中浸泡的原始方法。
工作原理,主要針對氟的化學成份,稀濃度,抓捕分析,在空調系統中追捕氟的泄漏量,氟的顆粒量少0.01的分之一,100%分析。






原理Principle
利用一個高的真空泵,將空調系統可能微泄的氟利昂吸入探測器,探測器采用高頻磁場低壓電離的工作方式,吸入微量的氟利昂,其液晶顯示數字立刻上升,同時蜂鳴器報警。
by using a high vacuum pump, the micro leak freon can to inhale detector, detector adopts low-voltage high frequency magnetic field ionization ways of working, inhaled trace of freon, the liquid crystal display Numbers rise immediately, at the same time a buzzer alarm.
技術The core features
1)持續穩定的工作
2)能檢測0.01ppm的氟利昂,相當于0.05克/年的泄漏量。
1) stable and reliable work;
2) the highest accuracy to detect 0.01 PPM of freon, equivalent to 0.05 g/leakage of the year.
典型效果Tical effect
1) 蒸發器檢漏,在確定漏點前,無須拆風口,拆儀表盤;
2) 可以檢測到老化的空調軟管滲漏(肥皂泡、熒光劑測不到的漏點);
3) 不制冷的汽車空調系統,不需要添加,即可檢測。
4) 看不到氣泡的氣門芯泄漏1秒鐘即可;
5) 半小時一輛車,檢測完畢,無須拆系統,無須水中浸泡;
1) the evaporator leakage, before determining leak point, do not need to diantle tuyere and tear open the dashboard;
2) can detect leakage of air conditioning hose aging (soap bubbles, fluorescent agent can't measuring leak point);
3) no refrigeration automobile air conditioning system, don't need to add freon, can detect.
4) 1 second can determined the leak valve core;
5) Half an hour to complete the detection of a car, no need to diantle the system, no water immersion;
使用介紹Method of use
蒸發箱,只要5分鐘,關閉空調,把探測器放在蒸發箱下面的風口,數字上升3-10左右,確定有漏。
the evaporation box: Five minutes is enough. Turn off the AC, and put the probe in tuyere on the bottom of the evaporation tank, figure up 3-10 or so, determine how leakage
在確定漏點前,無需拆風口before determined the leak point, with no need to open panel
壓縮機:只要5分鐘,探頭在機體,軸頭來回3-5次,數字上升5-15左右,確定有漏。
the compressor: Five minutes is enough.. Place the probe in the body and turn the head back and forth 3-5 times, and if the number rises by 5-15,then the leak is determined.
冷卻箱,10分鐘,把探頭隨著箱體結構來回均勻探測移動,數字上升,3-30左右,確定有漏。
the cooling tank: It takes about ten minutes. Move the probe with the body structure of the cooling tank at steady pace, and if the number rises by 3-30, then the leak is determined.
剩余管道的接頭處10分鐘把探頭隨管道走向來回3-5次,數字上升5-30左右,確定有漏。
the remaining of pipe joint: This step takes around ten minutes. Move the probe along the pipeline back and forth 3-5 times, and if the number rises by 5-50, then the leak is determined.













